Heating, Air Conditioning, and HVAC Repair Services in Westland, MI

Completed full system estimate for HVAC replacement on property with 16-year-old furnace requiring immediate replacement. Assessed existing exterior HVAC unit with associated refrigerant lines, electrical conduit routing, and ground-level installation conditions including weathered paver base and gravel bed. Evaluated electrical panel capacity and circuit breaker configuration to determine compatibility with new system requirements, documenting current wiring arrangement and available panel capacity for upgraded equipment installation.

Completed electrical estimate for new whole home generator installation at residential property. Evaluated existing electrical panel location in basement utility area and assessed exterior meter and service entry point on brick wall to determine optimal generator placement and electrical integration requirements. Documented current electrical infrastructure including panel capacity, conduit routing, and utility meter configuration to provide comprehensive proposal for generator system installation and transfer switch integration.

Completed full HVAC system installation including 70,000 BTU Lennox furnace and 2-ton air conditioning unit with rear placement. Installed integrated humidifier system with proper water supply connections and drainage. Ran refrigerant lines with insulation, installed PVC condensate drain and vent piping per code requirements. Connected electrical service, verified proper amperage and circuit protection. Completed all ductwork connections with proper sealing and insulation. System tested for proper operation, airflow, and refrigerant charge verified at factory specifications. All mechanical and electrical permits obtained and work performed to code compliance.

Responded to no heat call on 28-year-old forced air furnace system. Upon arrival, performed comprehensive diagnostic evaluation of the heating unit, inspecting all internal components including blower motor assembly, control board, electrical connections, and safety devices. Opened cabinet to access mechanical and electrical systems, examining capacitor, wiring harnesses, and refrigerant line connections. Assessed overall system condition given the advanced age of the equipment. Documented findings with photographs showing internal components, control board configuration, and wiring diagram specifications. Also performed requested air conditioning system inspection as part of the service visit.

Completed full HVAC system installation including 70,000 BTU furnace, 2.5 ton Lennox air conditioning unit, humidifier, and chimney liner in rear yard location. Installed outdoor condenser unit on mounting pad with proper gravel base and concrete paver surround, routed PVC condensate drainage lines, established electrical connections with disconnect box, and reconnected all utility services. All mechanical and electrical permits obtained and system fully operational upon completion.

Installed new 100-amp electrical service panel in residential property, including mounting panel box on interior wall, routing and connecting main service conductors, installing proper conduit runs, and establishing grounding connections. Coordinated installation with concurrent HVAC system upgrade requiring panel integration for 70K BTU furnace, humidifier, and 2.5-ton air conditioning unit. All work completed in accordance with requested electrical permits and current NEC code requirements.

Completed full HVAC system installation including a 70,000 BTU furnace and 2-ton air conditioning unit with rear yard condenser placement. Installation included all necessary venting with PVC piping, ductwork integration, electrical connections at dual meter setup, and system reconnection. All mechanical and electrical permits were obtained prior to installation, and the complete system was tested and verified operational in the utility room location.

Completed installation of 2.5-ton air conditioning system with evaporator coil at rear location of residence. Successfully obtained mechanical and electrical permits prior to installation, then installed new Lennox furnace with integrated coil, configured refrigerant lines, established proper drainage with PVC condensate piping, and reconnected all necessary electrical connections. System tested and operational upon completion.

Responded to service call for water heater with pilot light that repeatedly extinguishes. Inspected thermocouple, gas valve assembly, and venting system to diagnose ignition failure. Customer expressed interest in replacement unit if repair is not feasible.

Provided comprehensive estimate for complete HVAC system replacement including heating and cooling components for small to mid-sized residential application up to 1200 square feet. System specified for basement installation with natural gas or propane fuel source, evaluated existing electrical service infrastructure and utility meter configuration for compatibility with new equipment requirements. Assessment included review of current furnace or air handler location, existing ductwork layout, and PVC venting configuration to ensure proper integration of replacement system components.

Performed routine annual cooling maintenance on Carrier condenser unit. Inspected exterior grille panels, louvers, and cabinet condition, confirming proper structural integrity and airflow pathways. Customer requires replacement filters and evaporator pads at next service interval.

Responded to callback for 6-month-old air conditioning unit experiencing short cycling (4-minute intervals) and unusual noise that developed after earlier service visit same day. Upon arrival, performed comprehensive system diagnostics using Fieldpiece SMAN manifold gauge to measure refrigerant pressures, temperatures, and system performance parameters. Conducted thorough inspection of R-454B refrigerant system, checking for proper charge levels, pressures, and potential leaks. Utilized digital measurement tools to assess system temperatures and verify proper operation of components. Monitored superheat and subcooling values to ensure refrigerant charge was within manufacturer specifications. Identified and addressed the source of abnormal noise and short cycling condition. Verified all electrical connections, compressor operation, and control board functionality. System tested and confirmed operating properly with normal run cycles restored and noise eliminated.

Completed full HVAC system installation including 70,000 BTU gas furnace, 2-ton air conditioning unit with rear discharge configuration, humidifier, and flue liner. Obtained mechanical and electrical permits prior to installation, installed outdoor condenser on concrete pad with proper refrigerant line routing and electrical disconnect, and reconnected all necessary utilities to ensure complete system functionality.

Completed annual cooling maintenance on residential outdoor HVAC unit. Performed comprehensive inspection of condensing unit including heat exchanger coils, electrical connections, and refrigerant lines. All components found to be in operational condition with no immediate service needs identified.

Completed comprehensive HVAC estimate for full system replacement in residential property. Evaluated existing air handler unit with evaporator coil assembly, ductwork connections, and blower housing configuration, along with current furnace installation and water heater setup in basement utility area. Documented equipment conditions, system layout, and spatial requirements through detailed photographic assessment to provide accurate replacement specifications and installation planning for new HVAC system.

Responded to service call for 1-year-old outdoor A/C unit experiencing short cycling issue where system would kick on for 10 seconds then shut off repeatedly. Connected Fieldpiece manifold gauges to refrigerant lines to diagnose system pressures and temperatures. Unit remains under both parts and labor warranty coverage.

Conducted site evaluation for replacement estimate of 22-year-old residential HVAC system located on north side of property. Assessed existing furnace and non-operational air conditioning unit in mechanical room, documenting equipment configuration including air handler, ductwork layout, and clearance measurements. Evaluated exterior utility connections, electrical service accessibility, and equipment placement requirements to provide comprehensive replacement specifications for both heating and cooling systems.

Completed estimate for air conditioning system replacement on 16-year-old unit. Customer recently had furnace installed and is now seeking replacement of aging AC component. Assessed existing HVAC installation including air handler, ductwork configuration, and condensate drainage system with PVC piping. Provided replacement options and recommendations for new air conditioning system to integrate with recently installed furnace.

Provided comprehensive estimate for complete HVAC system replacement in basement location, including new furnace and air conditioning unit under BOGO promotion, as existing 10+ year old furnace was non-operational. Assessment included evaluation of current equipment setup featuring Aprilaire humidifier, existing ductwork configuration, and cramped mechanical room layout with concrete block walls. Additional estimate provided for electrical panel upgrade and installation of 220V outlets for dryer and stove applications to meet homeowner's requirements.

Completed comprehensive ComfortShield preventive maintenance on two outdoor condensing units at residential property. Performed thorough inspection of both systems, including visual assessment of condenser coils, fan operation, electrical connections, and refrigerant lines. Cleared debris and organic material from unit tops and surrounding areas, verified proper airflow through condenser coils, and confirmed both units were operating within normal parameters. All components found in satisfactory working condition with no immediate service needs identified.