Completed annual preventative maintenance on residential air conditioning system. Performed comprehensive tune-up inspection of outdoor condenser unit, verifying proper operation of all components, checking refrigerant levels, and confirming adequate airflow through coil fins and grille assembly. System operating within normal parameters with no issues identified; unit ready for upcoming cooling season.

Provided estimate for replacement of non-operational 1998 natural gas furnace located in basement. Unit had been shut off due to failure and required full system replacement. Assessed existing ductwork configuration, water heater proximity, and mechanical room layout to determine proper equipment sizing and installation requirements for new furnace system.

Completed comprehensive ComfortGuard maintenance visit on residential HVAC system, including full inspection and servicing of indoor furnace unit and outdoor condensing unit. Performed standard maintenance protocols on furnace including inspection of blower motor assembly, electrical connections, control panel operations, and PVC venting system integrity. Evaluated outdoor condenser unit condition, cleaned debris from surrounding area, inspected heat exchanger coils and fan assembly operation, and verified proper system performance for continued reliable heating and cooling operation.

Completed routine maintenance tune-up on one-year-old forced air furnace system. Performed comprehensive inspection of all internal components including blower motor assembly, electrical connections, control board, and safety devices. Verified proper operation of gas valve, ignition system, and heat exchanger. Checked and tested all wiring connections for secure contact. Inspected condensate drainage system and associated pump for proper function. Confirmed PVC intake and exhaust venting is clear and properly secured. Tested blower motor operation and verified airflow through system. All components operating within manufacturer specifications with no issues identified. Unit left in proper working condition.

Completed full HVAC system installation including 70,000 BTU furnace with liner and 2-ton Lennox air conditioning unit with rear discharge configuration. Installed humidifier, performed duct alterations in basement, and ran new dedicated electrical circuit with disconnect. All mechanical and electrical permits obtained and work performed to code specifications, with outdoor condensing unit mounted on composite pad with PVC condensate drainage and indoor air handler integrated with existing ductwork infrastructure.

Responded to no-heat call for commercial rooftop unit installed in 2021. Upon arrival, performed diagnostic inspection of RTU and removed access panels to troubleshoot system malfunction. Technician conducted thorough assessment of unit components to identify cause of failure and determine necessary repairs to restore heating operation.

Completed annual furnace maintenance and tune-up on 10-year-old heating system under Air Care Membership. Performed comprehensive inspection of furnace components, cleaned and serviced humidifier evaporator pad assembly showing mineral deposits, verified proper operation of water supply and drain lines, and inspected outdoor AC condenser unit. All systems tested and operating within normal parameters.

Successfully installed a ductless mini-split air conditioning system with indoor wall-mounted unit positioned high on the interior wall near the ceiling. Installation included mechanical and electrical work with new dedicated circuit to support the system. All necessary permits were obtained prior to installation, and the unit was mounted securely in accordance with manufacturer specifications and local code requirements.

Completed annual furnace maintenance tune-up as part of preventative care membership. Performed comprehensive inspection of all internal components including blower motor assembly, gas valve, ignition system, and electrical connections. All systems tested and operating within normal parameters with no issues identified.

Completed annual furnace maintenance on basement-located HDF90-11 model unit as part of preventative care membership. Performed comprehensive tune-up including inspection of blower motor assembly, gas valve connections, electrical wiring, and all internal components with access panel removed. Inspected and evaluated integrated humidifier unit with mesh filter pad and associated PVC drainage lines, confirming all systems operating within normal parameters with no issues identified.

# HVAC Maintenance - AHM Service Report Completed annual heating maintenance on 10-year-old furnace as part of scheduled membership service. Upon arrival, customer confirmed unit had been operating properly with no issues reported since previous service visit. Performed comprehensive tune-up inspection and testing of furnace system located in garage utility area. Conducted electrical diagnostics using digital clamp meter to verify proper amperage draw and voltage supply to blower motor and system components. All electrical readings were within manufacturer specifications. Inspected air handler unit, ductwork connections, and PVC condensate drain lines for proper installation and function. Verified 16x25x4 media filter was in acceptable condition with adequate airflow. Examined internal wiring, control board connections, and safety devices during service panel access. Tested system operation through full heating cycle to confirm proper ignition sequence, burner operation, and blower

Responded to service call for multiple electrical issues. Replaced malfunctioning bathroom fan control switch labeled "Fan Light" in children's room, featuring slider controls. Also serviced ceiling-mounted bathroom exhaust fan with square cover and horizontal ventilation slats, ensuring proper functionality. Diagnosed breaker panel issue and completed necessary repairs to restore system reliability.

Successfully installed a complete HVAC system including a new Lennox furnace (70,000 BTU) and 2-ton air conditioning unit. Work included installation of proper PVC venting, ductwork connections sealed with metallic tape, and addition of a humidifier. Removed existing chimney liner and reconnected all necessary electrical and plumbing components to ensure full system functionality.

Conducted comprehensive evaluation of 16-year-old AC and heating system for potential replacement. Inspected outdoor condenser unit mounted on concrete pad with associated electrical connections and refrigerant lines. Examined indoor ductwork configuration and copper line set routing in utility access area. Documented system condition and installation constraints to prepare detailed replacement estimate as requested by customer.

Completed installation of new complete HVAC system including a 70,000 BTU furnace and water heater. System was properly connected with appropriate vent piping, PVC connections, and copper plumbing lines. All mechanical, plumbing, and electrical work was completed with proper permits obtained and all manufacturer specifications followed.

Performed scheduled air conditioner maintenance and found condenser coils severely clogged with debris, significantly reducing system efficiency. Thoroughly cleaned condenser coils to restore proper airflow and heat exchange capability. Noted customer's request for line set foam insulation for future service.

Performed annual furnace maintenance as part of customer's membership program. Inspected and photographed interior components including the blower motor assembly, Honeywell control module, and electrical connections. Examined copper lines and wiring connections throughout the system, noting all components were in proper working condition with no issues identified.

Performed annual furnace maintenance as part of membership agreement. Conducted electrical testing using UEi DL379G multimeter, measuring amp draw on system components. Noted significant debris accumulation on outdoor condenser coil requiring cleaning to prevent efficiency loss and potential system damage.

Completed inspection of a 15-year-old non-operational furnace located in the basement. Documented existing HVAC system configuration including ductwork, ventilation piping, and connections to water heater. Provided replacement estimate for new furnace under current BOGO air conditioning promotion.

Completed service estimate for replacement of 16-year-old Bryant Plus 90 gas furnace and water heater located in basement. Current equipment is operational but aging. Documented existing installation including ductwork configuration, PVC ventilation system, and connection points to prepare comprehensive replacement proposal for high-efficiency alternatives.