Expert Heating and Cooling Services in Rochester Hills, MI

Performed site assessment for furnace installation in a residential property where gas line was recently installed on 03/19. Property has no existing furnace but contains an older A/C unit. Accessed attic space via pull-down ladder to evaluate installation requirements and potential system placement options. Customer is open to furnace-only solutions or combined furnace and air conditioning replacement packages.

Conducted full system evaluation of 1-year old Carrier unit for immediate replacement consideration. Inspected outdoor condenser unit (#36) installed on wooden platform and electrical panel to assess current system configuration and compatibility requirements for potential replacement. Service credit applied to estimate.

Responded to service call for a 13-year-old furnace with water accumulation underneath. Diagnostic inspection revealed severe corrosion and rust on critical components, particularly visible on copper/iron parts with extensive oxidation and structural deterioration. Evidence suggests prolonged moisture exposure has compromised system integrity.

Responded to no-heat call for 30-year-old forced air furnace system. Upon inspection, identified significant age-related deterioration in ductwork, particularly at the 90-degree elbow joint showing discoloration and dust accumulation. Serviced system and restored heating functionality.

Performed annual heating maintenance on furnace per Air Care Membership agreement. Inspected air filter and HVAC system components including filtration elements and condensate line. System was found to be in good working condition with no issues identified.

Completed installation of 70,000 BTU furnace and 2.5 ton AC system with humidifier. Addressed potential recall violation by providing required 1" clearance to combustibles above the plenum per safety standards. Completed all necessary mechanical reconnections and documented installation with verification photos.

Performed annual preventative maintenance on residential zone heating and cooling system. Inspected furnace interior components including blower motor assembly, control board, gas valve, and electrical connections; all parts were found in normal working condition with no signs of damage or excessive wear. System is operating as designed with no issues identified.

Responded to no-heat call on a residential forced air furnace system. Inspected the Honeywell Electronic Air Cleaner and replaced the dirty Filtrete 16x25 filter. Performed diagnostic on the furnace control board and electrical components, finding a failed limit switch which was preventing ignition. Replaced faulty limit switch, tested system operation through multiple heating cycles, and verified proper airflow and temperature rise.

Performed comprehensive annual furnace maintenance on 10-year-old unit with Clean Maintenance Warranty valid through 2025. Inspected and cleaned interior components including blower motor assembly, circuit board connections, and ventilation system, noting normal dust accumulation consistent with operational age. All electrical components and PVC drainage connections verified to be functioning properly with no issues detected.

Responded to service call for 17-year-old furnace located in basement with reported burning rubber smell and suspected blower motor issue. Upon inspection of the unit, performed diagnostic testing on the blower motor and electrical components. No visible damage was observed on the circuit board or wiring connections, but detected worn bearings in the blower motor causing the burning odor. Replaced blower motor assembly and performed system test to verify proper operation.

Diagnosed furnace reporting ignition/flame error (1 flashing light code). Inspection revealed functional gas valve assembly and pressure switch. System was successfully restored to normal heating operation with flame visible through heat exchanger vents.

Performed comprehensive evaluation of non-operational 20+ year old HVAC system. Identified need for complete furnace and air conditioning replacement due to system failure and age. Documented existing setup including ductwork configuration, ventilation system, and exterior condenser location for proper replacement specification and installation planning.

Performed scheduled Air Care Heating and Cooling maintenance. Inspected internal HVAC components including FASCO motor assembly and Teledyne gas valve. Replaced filter and humidifier pad as needed per maintenance protocol.

Installed a 70,000 BTU Lennox furnace with integrated humidifier system. Complete installation included proper venting with PVC pipe configuration, electrical connections, and condensate drainage setup. Final inspection confirmed proper operation of the new unit with all mechanical permits secured prior to installation.

Performed scheduled Air Care Heating and Cooling maintenance service. Inspected furnace interior, examining electrical components, circuit board connections, and gas valve assembly for proper operation. Replaced filter as needed per maintenance protocol.

Conducted estimate for full HVAC system replacement due to non-functioning heating unit. Inspected existing Bryant Plus 95 furnace installation in utility room alongside electrical panel and water heater. Evaluated current ductwork configuration, ventilation components, and PVC condensate drain lines to determine appropriate replacement system specifications.