Heating and Cooling Services in Plymouth, MI

# Tanked Water Heater Maintenance Service Performed comprehensive drain, clean, and flush service on tanked water heater located in basement. Accessed unit through exposed plumbing infrastructure and executed complete sediment removal procedure to restore optimal heating efficiency and extend equipment lifespan. Inspected surrounding plumbing connections, including hot water supply lines (red PEX), cold water supply lines (blue PEX with ball valve), and brass fittings for proper operation and potential issues. All isolation valves and connections were verified to be functioning correctly. Water heater tank showed normal wear patterns consistent with standard residential use. Flushing procedure successfully removed accumulated mineral deposits and sediment buildup from tank bottom. System was refilled, tested for proper operation, and confirmed to be heating efficiently with no leaks detected at any connection points.

Provided estimate for replacement of non-operational 20-year-old furnace located in basement. Customer expressed interest in Lennox high-efficiency furnace system. Assessed existing HVAC infrastructure including ductwork configuration, venting system with PVC piping, and current equipment layout in mechanical room to determine compatibility and installation requirements for proposed high-efficiency replacement unit.

Responded to callback for post-installation issues on 110,000 BTU furnace and 4-ton AC system. Accessed attic space to inspect exhaust vent pipe reported as crooked and potentially unstable on roof penetration. Upon inspection, found flexible exhaust duct secured with metallic foil tape running vertically through attic insulation to roof exit point. Assessed structural integrity and mounting of exhaust termination. Additionally investigated booster fan malfunction reported as continuously running since original installation. Documented attic conditions showing loose-fill fiberglass insulation and ductwork routing for warranty and quality assurance purposes.

Installed dedicated electrical circuit and wiring for double oven installation. Ran new copper conductors through basement ceiling joists to electrical panel, secured all wiring per code requirements, and connected circuit to appropriate breaker in main service panel. Verified proper voltage, tested circuit operation, and confirmed all connections were secure and compliant with electrical safety standards.

Completed routine Air Care Maintenance on residential outdoor HVAC unit. Performed comprehensive inspection of condenser coil, which showed clean fins in good condition with proper spacing and no debris buildup. Verified unit operational status, checked refrigerant lines, and confirmed proper drainage system function. All components operating within normal parameters with no service issues identified.

Completed annual heating maintenance on furnace system as part of membership service agreement. Performed comprehensive tune-up including inspection of internal components, electrical connections, and refrigerant lines. Verified proper operation of capacitor, relay connections, and wire harnesses throughout the unit. Tested system performance using digital measurement equipment to ensure optimal heating efficiency. All components found in acceptable working condition with no immediate repairs required. Unit operating within normal parameters upon completion of scheduled maintenance.

Completed estimate appointment for replacement of 33-year-old gas furnace in mobile home installation. Evaluated existing vertical furnace unit and outdoor condensing unit, documented current system configuration and condition through photographs. Provided equipment replacement options and discussed available furnace/AC promotion package with property owner.

Conducted on-site evaluation for new whole-home Kohler generator installation. Assessed existing electrical service panel location on exterior brick wall with current conduit routing, and inspected interior main electrical panel in basement to determine integration requirements for automatic transfer switch installation.

Completed annual furnace maintenance on 10-year-old unit as part of preventive membership service. Performed comprehensive tune-up including inspection of all major components, burner assembly cleaning, filter replacement, safety control testing, and system operational verification. Unit operating within normal parameters with no issues found.

Completed annual furnace maintenance and tune-up on brand new furnace system. Inspected air handler interior components, verified proper filter installation and condition of green filter media within white metal casing. Performed electrical diagnostics using clamp meter to measure current draw and verify proper system operation, tested all electrical connections and wiring throughout the cabinet. Checked condensate pump assembly and associated tubing for proper function. All components operating within manufacturer specifications, system ready for continued service.

Completed full HVAC system installation in basement utility area including 90,000 BTU high-efficiency furnace with humidifier, 3-ton air conditioning unit with rear placement, and residential water heater. All ductwork, ventilation piping, and electrical connections were installed per code specifications. PVC condensate and exhaust venting routed through ceiling joists with proper pitch and support. Sheet metal supply and return ductwork fabricated and connected to furnace plenum. Flexible duct transitions installed where required for equipment connections. Water heater positioned adjacent to furnace with appropriate clearances for service access. All gas piping, water lines, and drain connections completed and tested for leaks. Air conditioning refrigerant lines run to outdoor condenser unit and system charged to manufacturer specifications. Thermostat wiring pulled and connected to new furnace control board. Humidifier integrated into supply plenum with water line and drain installed

Successfully completed installation of a 3-ton air conditioning system with evaporator coil on the left side of the existing Rheem furnace unit. Installed new condensate drainage lines using PVC piping with proper pitch and secured all connections. Reconnected refrigerant lines, performed vacuum test, and charged system to manufacturer specifications. Mounted and secured all ductwork connections to the new coil, ensuring proper airflow and sealed all joints. Verified electrical connections, tested system operation through full cooling cycle, and confirmed proper condensate drainage. All work performed under proper mechanical and air conditioning permits, and system is operating within normal parameters.

Provided comprehensive electrical estimate for new whole home Kohler generator installation at a 2-story residential property. Assessed existing electrical service panel located in unfinished basement with exposed concrete block walls, evaluated current electrical infrastructure including main panel configuration and available capacity, and documented site conditions to determine optimal generator placement and integration requirements for complete home backup power system.

# HVAC Maintenance - AHM Service Report Completed annual complimentary heating maintenance inspection as part of Air Care Membership program. Performed comprehensive furnace tune-up on residential heating system, including visual inspection of all internal components, electrical connections, and mechanical assemblies. Accessed and examined blower motor, capacitor, gas valve assembly, control board, and associated wiring harness. All electrical connections verified secure with proper wire routing observed throughout unit. Inspected burner assembly components, heat exchanger access areas, and refrigerant line connections for proper installation and condition. Control board and safety devices inspected and found operational. Motor and moving components checked for proper operation. Documented system condition through photographic records showing internal component layout and current state of equipment. System found to be in satisfactory operating condition with no immediate service needs

Conducted an assessment for a tankless water heater replacement. Existing non-functional tankless unit was inspected, and photos were taken of the surrounding HVAC system showing the furnace with exposed internal components, circuit board, and various connections. Evaluation included examining the current venting system with PVC pipes along the ceiling and verifying utility connections for proper replacement installation.

Performed scheduled furnace maintenance as requested by customer. Inspected and serviced the brown furnace unit with appropriate warning labels and verified proper connection to insulated ductwork. System is functioning normally with maintenance completed to ensure optimal operation through the next cooling season.

Provided quote for replacement of 15-year-old non-functional natural gas furnace as part of BOGO promotion that includes AC unit #7. Equipment is located in customer's basement with existing water heater and PVC plumbing infrastructure.

Performed estimate for replacement of 32-year-old gas furnace system showing signs of leakage. Current installation includes aging Falco-branded furnace with Y-shaped ductwork configuration and connected humidifier, all located in basement. Unit is operational but requires replacement due to age and water leakage issues.

Completed comprehensive evaluation of HVAC system replacement needs for 2148 sq. ft. residence with existing Rheem furnace and 16-year-old Carrier 3.5 ton air conditioner. Inspection of basement utility area revealed new furnace installation with proper PVC venting system (purple primer marks visible at joints), while confirming the aging AC unit requires replacement. Documented current system configuration to prepare appropriate replacement options for the air conditioning component.

Completed annual heating maintenance on Lennox furnace as part of customer's maintenance membership. Performed comprehensive system inspection and tune-up, including examination of electrical components, blower motor, and ventilation system. All components found to be in proper working condition with no issues identified; system is operating efficiently with clean connections and properly configured drainage.